The technology for the production of gas technology allows you to create efficient economy-class models. These include Orion geysers. These instantaneous heaters are easy to operate, economical and safe. And most importantly, they are independent of seasonal outages. And gas outages are much less common than electricity. If comfort is dear to you, check out the products offered by Orion.
Features of gas columns "Orion"
Instantaneous water heaters are manufactured by a Chinese manufacturer. Wall-mounted columns are equipped with a heat exchanger, passing through which the water is heated. Automatic ignition allows you to get hot water immediately after opening the mixer.
The model range is represented by columns whose power is from 14 to 24 kW and productivity is from 7 to 12 l / min. This is enough to service several sampling points, take a shower and use a sink in the kitchen at the same time.
The modulation burner is equipped with a Winter-Summer regulator. So, in the summer, part of the burner is turned off to save fuel. And in winter, the regulator starts the burner again at full power to heat the water to a comfortable temperature.
Water heaters "Orion" work stably at a reduced - less than 0.025 MPa - pressure in the water supply. It is convenient for regions where water supply interruptions are frequent.
Design Features:
- Traction control sensor. Monitors the presence of ventilation in the chimney. In the event of a blockage or improper chimney arrangement, the draft ceases, which leads to carbon monoxide entering the room. To avoid this, the sensor disables the column.
- Flame ionizer. Controls the presence of flame in the burner. As soon as it goes out, the gas valve closes to prevent leakage.
- Drain valve or frost protection. Before a long shutdown of the equipment, water can be conveniently drained through the valve. Freezing, the liquid expands, which leads to pipe breakage. Therefore, when turning off for the winter, use the device.
- Switch-on protection without water or duct sensor. It captures the flow rate of water. If no fluid has entered the system, heating will not start.
- Safety valve. Discharges excess water with an increase in pressure of more than 1 MPa.
The devices are equipped with an open combustion chamber, so they are connected to a stationary chimney. Installation of the column is carried out in accordance with the instructions, and gas services are involved in the connection.
A series of Orion water heaters is presented by the models JSD14-D, JSD14-DS, JSD20 – D, JSD20 – DV and others. Between themselves, they differ only in technical characteristics. Therefore, we presented them in the table below.
Name | Model | ||||
JSD14-D | jSD20-D | JSD20-DK | JSD20-M | JSD24-M | |
Fuel type | Natural gas | ||||
Thermal Power (kW) | 14 | 20 | 20 | 20 | 24 |
Ignition Method | Electronic | ||||
Maximum and minimum pressure (MPa) | 0,02–1,0 | ||||
Productivity l / min | 7 | 10 | 10 | 10 | 12 |
Overall dimensions (HxWxD) | 472x303x140 mm | 600x345x175 mm | 520x320x180 mm | 590x340x180 mm | 610x350x180 mm |
The price of flowing heaters is from 11,000 rubles.
This is what users write in reviews of the Orion column.
Vladimir
A familiar master advised taking an Orion water heater. He said that although China, but good. Moreover, spare parts for it are a dime a dozen. You can take German equipment, but it is more expensive. And the JSD14-D model is inexpensive, it should last at least 5 years. Recently connected, satisfied with the work. True, sometimes the outlet water is too hot, but I learned how to regulate the temperature using a pressure tap.
Novel
A brother bought an Orion column two years ago. He does not complain, the equipment is functioning normally and does not consume much fuel.
Equipment malfunctions
Repair of the water heater can be performed independently if the cause of the failure is correctly determined. Why does the device fail? Consider common problems.
Instruments with a display can display error codes on the screen. Symbols indicate a specific system problem.
The burner does not light. The malfunction can be manifested by the error E6. If auto ignition does not turn on, you should check the batteries. They are mounted in a block at the bottom of the column. The unit is closed by a lid or screw cover. Open the cover and replace the shrunken elements.
Appliances with an open combustion chamber require good ventilation in the room. Open the window for fresh air. Check the chimney. Garbage from the street, foliage could get into the mine, soot accumulates on the walls. All this interferes with normal traction. Clean the shaft or contact your utility.
Leakage. Leakage may occur in the heat exchanger, water assembly, connections or pipes. It is important to check everything in sequence. If the problem persists, the pressure in the system will drop, as will the room temperature.
Inspect heat exchanger. If you notice green spots on the surface - these are signs of corrosion and the formation of fistulas. You can try to seal the damage. To do this, drain the water and dry the unit. Strip the damaged area with fine sandpaper and degrease with solvent.
Choose a soldering iron with a power of 100 watts or more. Heat it to 160 ° C. Use an aspirin tablet for flux, and tin for solder. The thickness of the solder should be at least 2 mm.
Check the water junction. To do this, turn off the water and fuel, dismantle the casing. Below the heat exchanger is a node. Remove it from the mounts and inspect. Additionally, it can be disassembled and the membrane and stem checked. If one of the elements is worn, replace it.
Make sure thread density. Connection points are one of the most vulnerable elements. If a leak is detected in them, either tighten the nuts or replace the gaskets. Turn off the water and unscrew the threads with a wrench. Remove the old gasket, remove deposits and degrease the area. Put a new gasket, reassemble everything in the reverse order.
Leak in the pipe is eliminated in the same way as in the heat exchanger - by soldering.
When ignited, the burner emits a flame. This is possible with:
- Badly open gas valve. Open to the end.
- Unstable pressure in the gas pipeline. Wait for recovery or call for service.
- Improper flame regulation. Change the position of the burner.
Cracking noise during operation. Clean the burner from soot and dust, descale the heat exchanger.
The smell of gas in the room. Fuel leak. Turn off the valves and open the window. Call the gas service.
When choosing a gas appliance, pay attention to the degree of its protection, the quality of the materials of manufacture. Once a year, check the equipment and carry out maintenance work.